A Step-by-Step Guide to Setting Up a Tub
A Step-by-Step Guide to Setting Up a Tub
Blog Article
What are your concepts about How to Install a Bathtub?
Setting up a tub isn't specifically rocket science, however it does call for solid plumbing, woodworking, and also in some cases, tiling skills. Replacing an old bath tub with a brand-new one is additionally a moderately difficult job. If the old bathtub is conveniently easily accessible, the task can move quickly; if you need to open a wall to remove the old tub and position the new bathtub, the task is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will need an assistant to leave the old tub and embeded in the brand-new one. Ensure you have qualified on your own for the task and fit trying it. Instead of hiring a specialist to take control of a halfway-completed job, it is better to consider utilizing one before you start. Possibilities are you might need a professional plumber to make tube links.
This short article will assist you set up a new bath tub in your restroom if you have already purchased a brand-new tub and do not require to alter the arrangement of your previous water system pipes.
Your devices as well as material list should make up the following:
Planning for the Setup
To start with, the sustaining framework provided with the bath needs to be fitted (if needed) according to the supplier's directions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is necessary to ensure that if the faucet comes with a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the taps device to prevent strain on the bathtub.
Fit the versatile faucet ports to the bottom of the two faucets using 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet with the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you use every one of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be suited its final placement.
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you ought to do is disconnect the water. After doing so, turn on the faucets to drain any water staying in the system. The process of getting rid of the existing faucets can be quite bothersome because of the restricted accessibility that is usually the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipes to the faucets. Have a towel ready for the continuing to be water that will come from the pipelines. When the supply pipelines have been eliminated, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this process. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Before moving on to fit the new faucets, compare the pipeline links on the old taps to the brand-new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Mounting the Bathtub
Making use of both wooden boards under its feet, position the bathtub in the needed setting. The wooden boards are practical in uniformly spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 little factors.
The next objective is to ensure that the tub is leveled all round. This can be attained by checking the level as well as changing the feet on the bath tub until the level reads level.
To set up faucets, fit the bottom of the outermost flexible tap port to the appropriate supply pipeline by making a compression join; after that do the same for the various other faucet.
Switch on the water system and check all joints as well as brand-new pipework for leakages and also tighten them if necessary. Fill the tub as well as also inspect the overflow electrical outlet and also the regular outlet for leakages.
Ultimately, fix the bathroom paneling as described in the manufacturer's instruction manual. Tiling and securing around the bath tub must wait up until the bathtub has been used at the very least when as this will certainly resolve it right into its last setting.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will certainly require a plastic adapter to stop damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end supplies a link to the current supply pipes.
If you need to fit a monobloc, then you will certainly require decreasing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin making sure that the washing machines remain in location between the tap and the sink. Secure the tap in position with the supplier given backnut. As soon as the faucet is safely in position, the supply pipes can be connected to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with regular faucet adapters. The previous kind needs to be attached to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the area where the bath meets the tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the installation can move sufficient to split a stiff seal, triggering the water to permeate the wall in between the bathroom and also the tiling, causing issues with moisture and possible leakages to the ceiling listed below.
You can select from a range of coloured sealants to assimilate your components and also fittings. They are sold in tubes and cartridges, as well as are capable of securing gaps approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with twists of soaked paper or soft rope. Bear in mind to always fill the bath tub with water prior to securing, to allow for the activity experienced when the tub remains in usage. The sealant can crack rather very early if you do not consider this movement prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also conveniently offered on the market. It is suggested to fit the ceramic tiles using water-resistant or water-proof adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy reading up on Installing A Bathtub? Try leaving feedback directly below. We'd be pleased to find out your views about this posting. We hope that you visit us again soon. Enjoyed reading our posting? Please share it. Let someone else locate it. We truly appreciate reading our article about How to Install a Bathtub Yourself.
Details
Report this page